Why are Type 3 & 4 Garments Constructed with a Sealed Seam?

Recently we have noted at least one garment on the European market with bound seams apparently certified to EN 14605, Type 4. There are several reasons why this cannot be correct and we would advise users be wary of such products; a bound seam is not a sealed seam and Type 3 and 4 garments should have sealed seams. This article explains why.

There are generally four types of seams used on disposable chemical protective workwear. “Serged” (i.e. stitched), “bound”, “welded” (either ultrasonically or other) and “stitched and taped”. Of these only the latter two, “welded” and “stitched and taped” seams provide a liquid tight seal. Serged and bound do NOT provide a seal as both feature holes through which the thread passes and through which any contaminant might penetrate or wick.

english_-bound_seam_construction.jpgThe bound seam in particular causes some confusion. In this the two fabric pieces are brought together in a “butt” configuration and a separate strip of fabric is wrapped around the two fabric edges and stitched into place along the length of the seam. Whilst this is arguably an improvement on a standard serged seam, it is not a sealed seam as it still features stitch holes – essentially open pathways through which a liquid or dust can penetrate – especially if the seam is subject to stress, so that the holes “open” to allow an even more free passage. In addition, the thread itself can be a likely route for a liquid to penetrate, as it often provides an excellent wicking medium.

This issue is important because while before 2005 there were a number of Type 4 garments on the market constructed with bound seams, since 2005 these have been withdrawn – for reasons that will become apparent below. However, we have recently become aware in Europe of some garments with bound seams, generally imported from Asian manufacturers and apparently certified to Type 4. This is dangerous. There are very good reasons why bound seams SHOULD, and at least one practical, standard-based reason why bound seams ARE excluded from use in Type 3 and 4 garments.

Why Bound Seams SHOULD be excluded for Type 3 and 4 garment construction

Bound_seam.jpgThe primary accepted purpose of Type 3 and 4 garments is to protect against hazardous liquid chemicals. In most cases these tend to be higher hazard chemicals; chemicals for which the consequences of the failure of protection, even for small amounts, might be relatively high (using the term “failure” to refer to some penetration of the liquid occurring). By contrast Type 6 applications tend to relate to liquids such as aerosol paints for which the consequences of failure are relatively low, so an unsealed seam is acceptable. Given that both Type 3 and 4 applications may result in a thorough soaking of the garment (the primary difference being in the pressure and nature of the spray) it would seem an unacceptably high risk to use a bound seam where the consequences of relatively small quantities of penetration might be grave.

stitched_and_taped_seam.jpgThus we would always recommend that any Type 3 or 4 garment should be constructed with a sealed seam. Until the last revision in 2005 of EN 14605, the standard for Type 3 & 4 garments, this was a matter of debate. Before then, the only aspect of the required testing that might be affected by the seam construction of a garment (excepting the seam strength) was the finished garment “Type” test, in which the suit is sprayed with a liquid, the spray type and pressure being adjusted for whether the test is Type 3 or Type 4. This assesses any penetration that occurs. In some cases this test did allow SOME garments constructed with bound seams to pass Type 4…and a number of such garments were on the market – though it must be said this was probably more a matter of good luck in the test rather than good planning or design of the garment. However, since the 2005 revision of the standard, a sealed seam has been a requirement of the standard – even if a requirement that is implied rather than implicitly specified.

Why bound seams ARE (now) excluded for Type 3 and 4 garment construction

One of the revisions in the 2005 update of the standard was in the requirements for permeation testing of seams against a chemical. The details are in clause 4.2:

en_14605_excerpt_clause_4.11_image_1.jpg

[Note: EN 463 and EN 468: in 2005 these were the standards for the finished garment spray tests (Jet and Spray). They have since been superseded by test numbers EN ISO 17491-3:2008 and EN ISO 17491-4:2008+A1:2016 thought the tests have not changed. The EN 14605 standard is currently under review and the references will be updated when any revised version is published.]

The key parts are highlighted. The clause references EN 14325:2003, clause 4.11. EN 14325 is the standard which defines all the performance classes:-

Clause_4.11_-_excerpt_from_EN_14325.jpg

Let’s summarize what these clauses imply.

1) The Type 3 & 4 standard EN 14605 states that any seams “exposed in use” should be tested for resistance to permeation of liquids according to clause 4.11 in the 14325 standard. What seams are “exposed in use”? Well for practical purposes we can assume all of them… I am not sure anyone would wish to base protection against a hazardous chemical on a guarantee that ANY seam on the garment is NEVER “exposed in use”!

2) The performance class achieved in the permeation test must be at least class 1 – or >10 minutes. (It might be argued that this statement only applies to the requirement for PB (Partial Body) garments – but this would be a manipulation of the standard and contrary to its basic intention  – what would be the point of having seams in partial body garments that achieve a minimum standard of class 1, whilst a full garment need only achieve less than a 10 minute performance?

3) Note that neither standard specifies a particular chemical to be tested. Thus the test can be on ANY chemical and whilst most reputable manufacturers undertake permeation tests against a range of chemicals, the standard actually requires that only ONE is tested and that a minimum performance of Class 1 is achieved.

In short, the EN14605 Type 3 and 4 standard requires that both fabric AND seam be tested for permeation resistance against at least 1 chemical and that a minimum performance of Class 1, or greater than 10 minutes, be achieved. And here is the point regarding seam construction. As we described a bound seam is not sealed; it has stitch holes. It is unfeasible that an un-sealed seam could achieve a class 1 in a permeation test against any chemical under any circumstances whatsoever. Quite simply, a bound seam simply could not pass this requirement; ipso-facto, no bound seam garment can be certified as Type 3 or 4.

Conclusion

It was for this reason that in the period following the 2005 revision of the Type 3 and 4 standard existing bound seam Type 4 garments were withdrawn from the market, and it is for this reason that NO Type 4 certified garments with bound seams should now be on the market. Any that are apparently so must be incorrectly certified and should be avoided.

There is a secondary conclusion from this; since 2005 all Type 3 and 4 garments should have at least one chemical permeation test on a seam which achieves at least Class 1. It would be worth confirming that this has been done on the garment you are using.

Facebook
Twitter
LinkedIn
Print
Email

Related Posts

Family walking through a doorway in the background as lab tech looks into the camera, protected by Lakeland Fire + Safety PPE
Protect What Matters Most: Proper PPE Use Can Save Your Family

Protect Loved Ones from Secondary Contamination with Proper PPE Personal Protective Equipment (PPE) is a crucial Barrier in safeguarding individuals...

Industrial worker wearing Lakeland Fire + Safety PPE working in hazardous area
Understanding Toxicity Levels and Protective Action Criteria

Toxic chemicals are different to most workplace hazards. Where most hazards have an instant effect and can be impossible to...

how to start evaluating your ppe text on splashed chemicals showing various chemical suits for protection by lakeland industries
Hazmat Suits & Chemical Handling: How to Start Evaluating Your PPE

Protecting people should be transparent. When you empower an employee with the right PPE and knowledge of the hazards they’re...

What can we help you find?

Find a Location

View Locations

Find a Chemical

Search Chemicals

Find a Download

Document Finder